会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 2. 发明专利
    • Power amplification circuit
    • 功率放大电路
    • JPS598412A
    • 1984-01-17
    • JP11807582
    • 1982-07-06
    • Pioneer Electronic Corp
    • ISHII SATORUITOU HIDEOSHINODA RIYUUICHI
    • H03F1/34H03F3/20
    • H03F1/34
    • PURPOSE:To improve considerably a voltage distortion at speaker terminals, by constituting the circuit so as to cancel the resistive component of a connecting cord connecting the power amplification circuit and a speaker, for enabling the speaker to drive completely. CONSTITUTION:The connecting cord 4 connecting a load such as speaker(not shown in figure) and the power amplification circuit 2 is inserted to one side of a bridge including operational amplifiers 8, 11, the resistive component is measured, a part of constants used for the measurement is taken in a current feedback network so as to constitute the circuit that the resistive component Rc of the connecting cord 4 is cancelled with output resistors R3, R4, Rf and Rb of the amplifiers 8, 11. Thus, the resistance value viewing the amplifiers 8, 11 from the speaker is almost zero, the speaker is driven with a full voltage and the voltage distortion at the speaker terminals is improved remarkably.
    • 目的:通过构成电路以消除连接功率放大电路和扬声器的连接线的电阻分量,从而显着提高扬声器端子的电压失真,使扬声器完全驱动。 构成:将连接诸如扬声器(图中未示出)的负载的连接线4和功率放大电路2插入到包括运算放大器8,11的桥的一侧,测量电阻分量,使用一部分常数 用于在电流反馈网络中进行测量,以便构成连接线4的电阻分量Rc被放大器8,11的输出电阻器R3,R4,Rf和Rb消除的电路。因此,电阻值 从扬声器观看放大器8,11几乎为零,扬声器以全电压驱动,并且扬声器端子处的电压失真显着提高。
    • 6. 发明专利
    • BIAS CONTROLLING CIRCUIT
    • JPS58133011A
    • 1983-08-08
    • JP1520182
    • 1982-02-02
    • PIONEER ELECTRONIC CORP
    • ITOU HIDEO
    • H03F1/30H03F3/20H03F3/213H03F3/30
    • PURPOSE:To keep the fluctuation always at a constant level for the DC bias current of an output transistor, by comparing the both-terminal voltage of an impedance element with the reference voltage and then controlling the voltage between control inputs of the output transistor with a signal corresponding to the difference between said both-terminal voltage and the reference voltage. CONSTITUTION:A pair of level comparing differential amplifiers 2 and 3 are provided to generate the control voltage of a bias voltage controlling circuit 1. The amplifier 2 contains a pair of differential transistors TRQ10 and Q12 which use the both-terminal voltage of an emitter resistance R3 of an output TRQ4 and the reference voltage +E1 as the differential input. The collector output of the TRQ10 is used to a base control signal of a TRQ5. While the amplifier 3 contains a pair of differential TRQ11 and Q13. The collector output of the TRQ11 is used to the base control signal of a TRQ9. Then the base control input voltage of the TRQ5 and Q9 respectively is varied to control the voltage among base control inputs of output TRQ2-Q5.
    • 8. 发明专利
    • FEEDBACK AMPLIFIER CIRCUIT SYSTEM
    • JPS59119906A
    • 1984-07-11
    • JP22809682
    • 1982-12-27
    • PIONEER ELECTRONIC CORP
    • ISHII SATORUITOU HIDEO
    • H03F1/34
    • PURPOSE:To improve both the distortion in a wide band range as well as the input/output impedance by having a term (alpha+Stau), (where alpha, S and tau show a constant, jw and a time constant respectively) for each feedback circuit of a multiplex feedback amplifier circuit system. CONSTITUTION:N units of amplifier groups 1-N are cascaded with each other, and amplifiers 2-N have a pole with 1/tau0 respectively. While amplifiers 2- (N-2) have a zero point with 1/tauX each. A feedback circuit having a transmission function tauF(1-Stau0)/tau0 is provided between an input-output joint of each amplifier and the circuit output OUT from the amplifier 1 to amplifiers (N-1) to form a multiplex loop. Then a feedback circuit having a transmission function beta is provided between the output OUT and the circuit input IN. Here a fixed gain tau0/tauF is obtained with the characteristics up to 1/tau0 in case no outermost feedback loop is applied. This gain reduces at 6dB/OCT with 1/tau0-1/tauX and set at 12dB/OCT with >=1/tauX. Thus it is possible to apply stably a feedback using the outermost loop up to 1/tauX.