会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 1. 发明专利
    • In-tunnel position grasping system
    • 隧道定位系统
    • JP2009019400A
    • 2009-01-29
    • JP2007182187
    • 2007-07-11
    • East Japan Railway CoJr Higashi Nippon Consultants Kkジェイアール東日本コンサルタンツ株式会社東日本旅客鉄道株式会社
    • KOBAYASHI KEIICHIHORIGUCHI HIROYUKISATO KATSUTOSHIHASEBE KUNIHIKO
    • E21F17/18
    • PROBLEM TO BE SOLVED: To grasp a position of a mobile station in a wider range in a tunnel by a system configuration simpler than an IC-tag laying system.
      SOLUTION: In this in-tunnel position grasping system, fixed stations 1a-1e arranged at each interval of 50 m in the tunnel are connected to each other via a power cable 3, and a control unit 10 enables data communication with the respective fixed stations 1a-1e via the power cable 3. A UHF radio response request signal is given to the mobile station 2 from the fixed stations 1a-1e, and the mobile station 2 sends out ultrasonic waves in response to it. Each of the fixed stations 1a-1e measures an ultrasonic wave arrival time until the ultrasonic wave sent out of the mobile station 2 reaches each of the fixed stations 1a-1e; and the control unit 10 collects the ultrasonic wave arrival time from the respective fixed devices 1a-1e, and acquires a distance from each of the adjacent fixed stations 1a and 1b to the mobile station 1 from the ultrasonic wave arrival time so as to determine a position of the mobile station 2.
      COPYRIGHT: (C)2009,JPO&INPIT
    • 要解决的问题:通过比IC标签铺设系统简单的系统配置来掌握在隧道中更宽范围内的移动台的位置。 解决方案:在这种隧道内位置抓取系统中,隧道中以每个间隔50m布置的固定站1a-1e经由电力电缆3彼此连接,并且控制单元10能够与 通过电力电缆3连接各个固定电台1a-1e。从固定电台1a-1e向移动台2提供UHF无线电响应请求信号,并且响应于移动台2发送超声波。 每个固定站1a-1e测量直到从移动站2发出的超声波到达每个固定站1a-1e为止的超声波到达时间; 并且控制单元10从各个固定设备1a-1e收集超声波到达时间,并且从超声波到达时间获取与每个相邻的固定站1a和1b相对于移动站1的距离,以便确定 移动台2的位置。版权所有(C)2009,JPO&INPIT
    • 2. 发明专利
    • Drawing production system, plotting method, and program
    • 绘图生产系统,绘图方法和程序
    • JP2006018118A
    • 2006-01-19
    • JP2004197273
    • 2004-07-02
    • Jr Higashi Nippon Consultants KkKozo Keikaku Engineering Incジェイアール東日本コンサルタンツ株式会社株式会社構造計画研究所
    • HIRAI KAZUTOHASEBE KUNIHIKOKATO MAKIMATSUMOTO HIROTOSHI
    • G09B29/00G06T11/60
    • PROBLEM TO BE SOLVED: To provide a drawing production system which automatically produces railroad wiring schematic drawings of an assigned region and produces the schematic drawings imparted with a deformation feeling thereto while keeping topology.
      SOLUTION: When the drawing production system receives the instruction of a schematic drawing producer, a controller 110 first determines the coordinates on the railroad wiring schematic drawings of respective points on the basis of the numerical value maps, mileage information, etc., stored inside a memory section 120. Next, the controller deletes the points which are contiguous with next door and have reduced differences in inclinations of the segments before and behind the same. The controller maps the points set on the lines on the grid points on grids set at prescribed intervals in compliance with the determined coordinates. The points not set on the lines are mapped regardless of the grids. Finally, the railroad wiring schematic drawings are output from an output device 14 in compliance with the mapped results.
      COPYRIGHT: (C)2006,JPO&NCIPI
    • 要解决的问题:提供一种绘图生产系统,其自动生成分配区域的铁路布线示意图,并产生赋予其变形感的示意图,同时保持拓扑。 解决方案:当绘图生产系统接收到示意图制作者的指令时,控制器110首先基于数值图,里程信息等来确定各点的铁路布线示意图上的坐标, 存储在存储器部分120内。接下来,控制器删除与隔壁相邻的点,并且减少了在其前后的片段的倾斜度的差异。 控制器根据确定的坐标将设置在网格上的线上的点设置为按规定间隔设置的网格。 无论网格如何,不会设置在线上的点。 最后,根据映射结果从输出装置14输出铁路布线示意图。 版权所有(C)2006,JPO&NCIPI