会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 2. 发明授权
    • Command queuing smart storage transfer manager for striping data to raw-NAND flash modules
    • 命令排队智能存储传输管理器,用于将数据分配到原始NAND闪存模块
    • US08176238B2
    • 2012-05-08
    • US13104257
    • 2011-05-10
    • Frank YuCharles C. LeeAbraham C. Ma
    • Frank YuCharles C. LeeAbraham C. Ma
    • G06F12/00G06F13/00G06F13/28
    • G06F12/0246G06F3/061G06F3/0659G06F3/0688G06F12/0607G06F2212/7208G11C13/0004
    • A flash module has raw-NAND flash memory chips accessed over a physical-block address (PBA) bus by a NVM controller. The NVM controller is on the flash module or on a system board for a solid-state disk (SSD). The NVM controller converts logical block addresses (LBA) to physical block addresses (PBA). Data striping and interleaving among multiple channels of the flash modules is controlled at a high level by a smart storage transaction manager, while further interleaving and remapping within a channel may be performed by the NVM controllers. A SDRAM buffer is used by a smart storage switch to cache host data before writing to flash memory. A Q-R pointer table stores quotients and remainders of division of the host address. The remainder points to a location of the host data in the SDRAM. A command queue stores Q, R for host commands.
    • 闪存模块具有通过NVM控制器通过物理块地址(PBA)总线访问的原始NAND闪存芯片。 NVM控制器位于闪存模块或固态硬盘(SSD)的系统板上。 NVM控制器将逻辑块地址(LBA)转换为物理块地址(PBA)。 闪存模块的多个通道之间的数据条带化和交织由智能存储事务管理器控制在高电平,而在信道内的进一步的交织和重新映射可由NVM控制器执行。 智能存储交换机使用SDRAM缓冲区,在写入闪存之前缓存主机数据。 Q-R指针表存储主机地址的商和余数。 剩余部分指向SDRAM中主机数据的位置。 命令队列存储主机命令的Q,R。
    • 3. 发明授权
    • USB package with bistable sliding mechanism
    • USB双卡双待滑动机构
    • US08102662B2
    • 2012-01-24
    • US12552250
    • 2009-09-01
    • Siew S. HiewNan NanAbraham C. Ma
    • Siew S. HiewNan NanAbraham C. Ma
    • H05K7/12
    • G06F1/1632H05K5/0278
    • A USB device including a bistable mechanism that serves to bias a plug connector into one of two stable states, where the first stable state is associated with a retracted position in which the plug connector is fully retracted inside a housing, and the second stable state is associated with a deployed position in which the plug connector extends through the front opening for coupling to a host system. Movement of the plug connector form the retracted to the deployed position is performed by manually applying a force to a handle portion that protrudes through a slot defined in the housing. The bistable mechanism resists the deploying force until an equilibrium point is reach, after which the bistable mechanism releases stored potential energy to complete the deploying process and to maintain the plug connector is the deployed position.
    • 一种USB装置,包括用于将插头连接器偏置成两个稳定状态之一的双稳态机构,其中第一稳定状态与插入连接器完全缩回到壳体内的缩回位置相关联,并且第二稳定状态为 与展开位置相关联,其中插头连接器延伸穿过前开口以联接到主机系统。 插头连接器的移动通过手动施加到通过限定在壳体中的狭槽突出的手柄部分来执行。 双稳态机构抵抗展开力直到达到平衡点,然后双稳态机构释放存储的势能以完成部署过程并保持插头连接器处于展开位置。